Post #1
cylinder block
|
displaying posts 1 to 11 of 11
| Author | Subject: wanted |
 mick1989
Regular  Location: preston Registered: 13 Dec 2010 Posts: 123 Status: Offline |
|
 Posted 30th Oct 2011 at 17:03
|
|
|
fordygti
Seasoned Pro  Location: Walpole St Andrew Registered: 07 Dec 2009 Posts: 1,257 Status: Offline |
Post #2
Post in the Wanted section, you will get more views and get more chance of getting one.  ________________________________________ 98 onyx black 306 Rallye53 Nissan Primastar silver (work horse) 58 black Volvo c30 sport |
|
Posted 30th Oct 2011 at 17:05
|
|
|
owain
Seasoned Pro  Location: Essex Registered: 20 May 2009 Posts: 9,185 Status: Offline |
Post #3
And change the subject line to something more useful.________________________________________ Membership expiring soon, get in contact on our new little forum project. |
|
Posted 30th Oct 2011 at 17:10
|
|
|
jonnie205
Seasoned Pro Location: Bicester Registered: 10 Apr 2005 Posts: 4,146 Status: Offline |
Post #4
£40 |
|
Posted 30th Oct 2011 at 18:08
|
|
|
pugjim
Seasoned Pro  Location: Sheffield Registered: 11 Mar 2007 Posts: 1,380 Status: Offline |
Post #5
I have a complete bottom end in good condition from a good running engine for £50 |
|
Posted 30th Oct 2011 at 21:02
|
|
|
mick1989
Regular Location: preston Registered: 13 Dec 2010 Posts: 123 Status: Offline |
Post #6
whats the millage |
|
Posted 31st Oct 2011 at 01:20
|
|
gnrlee
Forum Admin Location: Leeds Registered: 20 Aug 2005 Posts: 8,878 Status: Offline |
Post #7
I'll vouch for Jims! I run about on it while mine was being worked on run spot on!  ________________________________________ Proud Member of the ASTOR Owners Club |
|
Posted 31st Oct 2011 at 02:26
|
|
|
pugplus!
Seasoned Pro  Location: Pontypool (southwales) Registered: 13 Feb 2009 Posts: 3,379 Status: Offline |
Post #8
Hi there, did you want a complete bottom end or just a bare block?Many thanks,richard. ________________________________________ Pugplus Peugeot parts specialists!!1000`s & 1000`s of new & used parts in stock International shipment Genuine Peugeot parts suppliers A range of Peugeot's for sale Contact info: Mob:07532066648 (richard) Email: pugplus@hotmail.com |
|
Posted 31st Oct 2011 at 16:31
|
|
|
mick1989
Regular Location: preston Registered: 13 Dec 2010 Posts: 123 Status: Offline |
Post #9
ive had a cambelt snap just built the top end. the cambelt tensioner pulley has snapped the block were it sits on to. sush a shame as the car only done 65000 just the bare block will be fine. |
|
Posted 31st Oct 2011 at 19:56
|
|
|
welshpug!
Capt Pedantic  Location: Bigend, Wales. Registered: 27 Mar 2007 Posts: 25,817 Status: Offline |
Post #10
just drill the bolt out?________________________________________ need a part number? get on here - http://public.servicebox.peugeot.comBring on the Trumpets. |
|
Posted 31st Oct 2011 at 19:59
|
|
|
mick1989
Regular Location: preston Registered: 13 Dec 2010 Posts: 123 Status: Offline |
Post #11
its not the bolt that had snapped. was the cast bracket on the block were the tensioner mounts to. sorted itt today tho. drilld n tapped a new hole just below the original 8) |
|
Posted 1st Nov 2011 at 18:54
|
|
The Peugeot GTi-6 & Rallye Owners Club - ©2024 all rights reserved.
Please Note: The views and opinions found herein are those of individuals, and not of The Peugeot 306 GTi-6 & Rallye Owners Club or any individuals involved.
No responsibility is taken or assumed for any comments or statements made on, or in relation to, this website. Please see our updated privacy policy.